Nízkopodlažný náves

MÜLLER-MITTELTAL 3- achs Satteltiefl.-Luft-Lenk-hydr. Auffahrram.

Stav: nový, maximálna hmotnosť nákladu: 38 290 kg, celková hmotnosť: 48 000 kg, konfigurácia náprav: 3 nápravy, dĺžka ložného priestoru: 8 500 mm, šírka ložného priestoru: 2 520 mm, Rok výroby: 2026, * TS 3 Profile 30.0: ----Braking System: * Wabco EBS-E (Electronic Braking System) * Emergency release system for spring brake actuators * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Last axle is trailing-steered with electro-pneumatic steering lock ----Suspension: * Air suspension with lifting/lowering device and RtR valve ----Electrics / Lighting: * Tire Pressure Monitoring System (TPMS) * Smartboard control unit mounted on trailer as information terminal with pressure sensors for total axle load display * 15-pin electrical connector Hjdpfx Aspk D I Asa Iok * LED lighting system 12 / 24V * Removable LED rotating beacon at rear left ----General Attachments: * Side underrun protection * Landing gear at the front and mechanical swing-out supports at the rear of the chassis * Straight steel mudguards * Spare wheel carrier mounted on the right side under the chassis ----Low-bed Surface: * Saddle platform with 45° chamfered front corners and front toolbox made from galvanised steel plate, dimensions: W = 2,480 x H = 500 x L = 665 mm, with folding lid * 400 mm aluminium side boards (RAL 9010 pure white), foldable and removable on the sides of the saddle platform * Rear panel 150 mm high, slotted in * Rear bevel on the saddle platform to the low-bed, approx. 700 mm long * Saddle platform with 50 mm wooden planks and low-bed platform with 60 mm wooden planks * Chequer plate above the axles ----Widenings: * 8 mechanical folding extensions to 3 m overall width (extensions not present in the rear slope; planks for extension provided with storage on the saddle platform) * Mechanically adjustable warning board sets front and rear ----Load Securing (Lashing Package): * On the saddle platform: 2 x 6.3 t lashing rings each as well as 3 x 5 t lashing bars per side on the outer frame * On the low-bed: 2 x 13.4 t lashing rings per side and 4 x 10 t swingable/lowerable lashing rings recessed in the outer frame * 2 x 6.4 t lashing eyes per side and 1 lashing ring in the excavator arm rest at rear * 2 x container locks directly after the gooseneck in the low-bed platform ----Excavator Arm Rest: * Excavator arm rest runs continuously from end of last rigid axle over steering axle to end cross member with integrated reinforcement profile, approx. L = 2,450 x W = 770 x D = 270 mm ----Loading Ramps: * Mechanical, single-piece, hot-dip galvanised hydraulic access ramps, approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way control valve for possible later retrofit of hydraulic ramp shift by customer * Outer board of the ramp made from 50 mm hardwood * Climbing laths on the outer frame of the ramp and on the approach slope ----Hydraulics: * Hydraulic oil flow divider in trailer (for hydraulic pump output in truck from over 40 l/min to 120 l/min) ----Loading Dimensions: * Saddle platform loading area: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Loading height unladen approx. 910 mm (including 860 mm approach slope) ----Fifth-Wheel Height: * Approx. 1,220 mm (suitable for 2- and 3-axle tractors) ----Paint Coating: * Chassis, ramps, rear folding supports, widening consoles all hot-dip galvanised * Axles, landing gear, air tanks painted in black * Vehicle is hot-dip galvanised ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Sample images may depict equipment not included in the offered vehicle ----Delivery Time: * Available from week 26/2026

Stav: použitý, najazdené kilometre: 1 400 km, výkon: 43 kW (58,46 k), prvá registrácia: 07/2008, typ paliva: nafta, celková hmotnosť: 4 900 kg, farba: oranžová, typ prevodu: mechanický, zavesenie: iný, prevádzkové hodiny: 1 400 h, Výbava: klimatizácia, pohon všetkých kolies, STK a EK nové, 08.07.2008, 1 400 motohodín, 43 kW, 2 746 cm³, priemyselný čelný nakladač, diesel, pohon všetkých kolies, kabína, klimatizácia, Hydraulic Shuttle, trávne pneumatiky, možné poľnohospodárske pneumatiky, prípustná celková hmotnosť 4 900 kg. PRE NÁS JE ROZHODUJÚCI STAV A POCIT ZO STROJA, CENA JE DRUHORADÁ. V prípade ďalších otázok je vám k dispozícii pán Faller na čísle telefónu. //*VÝMENA, PROTIÚČET ALEBO ZALOŽENIE VÁŠHO VOZIDLA, AKO AJ FINANCOVANIE MOŽNÉ! Všetky údaje bez záruky.* Ďalšie ponuky nájdete na našej webovej stránke. Popis a uvedené údaje nepredstavujú záväzný prísľub. Záväzná je iba kúpna zmluva uzatvorená v autosalóne pri kúpe vozidla. Zmeny, chyby a medzipredaj vyhradené! Hedsvidc Aopfx Aa Iok

Stav: veľmi dobrý (použitý), konfigurácia náprav: 2 nápravy, prvá registrácia: 03/2015, dĺžka ložného priestoru: 134 450 mm, šírka ložného priestoru: 2 550 mm, výška ložného priestoru: 480 mm, zavesenie: hydraulika, Rok výroby: 2015, Výbava: ABS, = Ďalšie možnosti a príslušenstvo = - Centrálne mazanie = Ďalšie informácie = Konfigurácia náprav Hsdpfx Aajvtc Aij Isk Odfedrenie: hydraulické odfedrenie Zadná náprava 1: Max. zaťaženie nápravy: 12 000 kg; Riadená Zadná náprava 2: Max. zaťaženie nápravy: 12 000 kg; Riadená Hmotnosti Prevádzková hmotnosť: 12 660 kg Užitočné zaťaženie: 34 340 kg Celková prípustná hmotnosť: 47 000 kg Funkčné Výška ložnej plochy: 48 cm Vysúvateľná nadstavba: Áno Stav Technický stav: veľmi dobrý Vizuálny stav: veľmi dobrý Finančné informácie Cena: Na vyžiadanie Ďalšie informácie Pre viac informácií kontaktujte Davida F. Middelmana.

Stav: nový, maximálna hmotnosť nákladu: 67 200 kg, celková hmotnosť: 85 000 kg, konfigurácia náprav: 3 nápravy, celková šírka: 2 540 mm, Výbava: ABS, You can find our complete vehicle inventory, including immediately and soon-available vehicles, on our website. Excerpt from equipment. Full specification available on request. GOOSENECK * Gooseneck in SNT design to optimize platform length, approx. 3,700 mm long, rear tapered approx. 1,000 mm x 10° * For tractors: 6x2, 6x4, and 8x4 short wheelbase * Steel front wall, removable, approx. 400 mm high * 3 kW electro-hydraulic power pack for controlling hydraulic operations, except for hydraulic winches * Outer beams of gooseneck with mounting holes for bolted lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of removable ALU side walls, approx. 400 mm high, anodized * 1 removable ALU rear wall, approx. 400 mm high, anodized * Over the gooseneck, approx. 40 mm thick hardwood floor; over the king pin, checker plate floor Hodpergzv Nefx Aa Iek * 3.5-inch king pin * Guide plate from gooseneck for fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection panel (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow control, incl. cabling bracket for supply lines (Faymonville couplings) * 2 pairs of stake pockets recessed into the gooseneck for approx. 100 x 50 mm plug-in stakes PLATFORM * Extendable platform, approx. 11,000 mm long, rear tapered approx. 500 mm x 10° * Pneumatic locking with conical lock bolts and reinforced lock positions; supply lines protected within the extendable rails and automatically adjust to the platform length * BPW axles and suspension, 1st axle steered ahead, 2nd axle fixed, all other axles hydraulic-mechanical forced steering * 1st axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with raise/lower valve * Tires: 235/75 R 17.5 3PMSF twin tires * Mechanical landing gear with two-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Platform with continuous and between the axles interrupted approx. 50 mm thick hardwood flooring (increases friction coefficient) * Long holes for attachable and repositionable bridging elements: – at the fixed section behind the gooseneck – at the front of the platform * 1 sliding intermediate platform, approx. 500 mm wide, for the extension tube with large cross-section, with checker plate floor, front and rear with long holes for attachable and movable bridging elements * 1 pair of recessed flat lashing rings in the fixed front platform section (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the platform, folding outward (LC 10,000 daN) * 1 pair of mechanical rear supports * Steering from front and rear operated via cable remote control, with single-track alignment of the axles, without installation in the tractor * 1st axle with automatic lift-axle function and starting aid in accordance with EU regulation 2021/535 * Under the gooseneck and at the rear cross-member, left and right, each with a 7-pin socket and holder for warning plates * Painted sand coating on the outer frame of the platform as well as on the checker plates and the transition area between the platf

Stav: nový, celková hmotnosť: 49 500 kg, konfigurácia náprav: 3 nápravy, Rok výroby: 2026, 3-axle MULTIMAX PLUS low-bed semi-trailer, air-suspended and with hydraulically forced-steered axles. Technical data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h (legal) Gross vehicle weight: 49,500 kg (depending on fifth-wheel load) Fifth-wheel load: 18,000 kg Axle load: 31,500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Turning radius king pin to rear approx.: 2,100 mm Fifth wheel height loaded approx.: 1,205 mm Loading platform length approx.: 9,600 mm Extendable by approx.: ? Platform width approx.: 2,540 mm Loading height (max. loaded) approx.: 890 mm Suspension travel approx.: -55/+145 mm Axle spacing: 1,360 mm Gross weight dependent on fifth-wheel load: Yes Special permit required if national legislation is exceeded. Technical description Gooseneck: Gooseneck in SNT design for optimized platform length, approx. 3,900 mm in length, rear with bevel approx. 1,000 mm x 6°. Technical fifth-wheel load: 18,000 kg. For tractor units: 4 x 2 and 6 x 2. Platform: Platform approx. 9,600 mm long with rear ramped bevel approx. 900 mm x 6°. Platform section after gooseneck is hydraulically liftable and lowerable, length approx. 3,000 mm, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS One pair of two-part AXS steel ramps, approx. 4,920 mm long and approx. 900 mm wide. Open grid surface. Hydraulic folding ramp ends. Each ramp hydraulically adjustable outwards by approx. 235 mm and inwards by approx. 365 mm. Max load and gradient as per data sheet: C470319 Maximum incline with lowered platform: 9° Axles and suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg Air suspension with lift and lower valve. Axle tools. Tyres: 235/75 R 17.5 3PMSF twin tyres. Brand at our discretion. Load index 143/141J (144/144F). Brake system: Braking system by WABCO EBS-E, in accordance with EU regulations. No connection cable to tractor unit. Lighting: 24V lighting system “ASPÖCK-NORDIK full LED” compliant with EU regulations. (ASS 3) Metallisation: Complete HRM metallization (High Resistance Metallisation) Hjdpfx Ajizu Ntsa Isk Entire steel construction shot-blasted, then finished with ZINACOR 850 (Zinc 85% - Alu 15%). Paint finish (6-stage final treatment): Complete steel structure shot-blasted after welding. 1 layer zinc-based primer, 1 adhesion primer layer. Final finish with 2 layers of 2-component paint (acrylic), single color in RAL color of choice, then cavity sealing with special wax. Rims in silver. Multi-color and special paint at extra cost. Steel construction: Made from high-strength fine-grained steel. Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa). Welders certified DIN-EN 287-1. MAG welding as per EN ISO 4063. Shielding gas M21 as per EN ISO 14175 Front wall: Steel, removable, approx. 400 mm high. Supply line junction box to tractor unit, fitted at the level of the outer frame profile. ASPÖCK-UNIBOX at front junction rail with sockets: 24N, 24S & 15-pin. 24N connection as per ISO-1185 24S connection as per ISO-3731 15-pin as per ISO-12098 If your pin configuration deviates from ISO standards, please inform us. “Anderson” socket on front junction box (Rema 78051-00 and Amp. 150 V.) Cable for supply of the electro-hydraulic pump unit and/or electric winch (35 mm²,

Stav: nový, maximálna hmotnosť nákladu: 31 500 kg, celková hmotnosť: 42 000 kg, konfigurácia náprav: 3 nápravy, Rok výroby: 2025, Výbava: ABS, Wiese 3-axle semi-trailer with lift table and folding rear section. Perfect for transporting forklifts and/or work platforms. Technical specifications: - 3 x 10 t axles - Lift axle - Steering axle with Smart Steering (steers both forward and backward) - Outer beam chassis with inclined frame - Neck construction rated for 18 t, suitable for 2- and 3-axle tractor units - Hydraulic lift table adjustable to 3 positions - Rear in folding tail design with hydraulic extensions, usable as drive-on ramps, bridging ramp, or loading platform (overall length reduced with rear upright) - Remote control for ramps and lift table - Front wall - Grating floor - Numerous lashing points - SmartBoard - Central lubrication system Hedpsvw Hmtjfx Aa Iek - Steel construction, shot-blasted, hot-dip galvanized and painted Various optional extras available: For example: - Winch - Toolbox on fifth wheel step - Alloy wheels Further information on request.

Stav: použitý, pohotovostná hmotnosť: 9 480 kg, maximálna hmotnosť nákladu: 31 520 kg, prvá registrácia: 03/2020, ďalšia kontrola (TÜV): 04/2024, celková dĺžka: 11 500 mm, celková šírka: 25 500 mm, celková výška: 38 000 mm, zavesenie: vzduch, veľkosť pneumatiky: 245/70 R 17.5/10mm, rázvor náprav: 1 800 mm, veľkosť prednej pneumatiky: 245/70 R 17.5/10mm, prevádzková hmotnosť: 41 000 kg,

Stav: použitý, celková hmotnosť: 45 000 kg, konfigurácia náprav: 3 nápravy, prvá registrácia: 09/2017, * Nápravy SAF * Kolískové vaničky * Hydraulické nakladacie rampy nastaviteľné na šírku * Vzduchové odpruženie Hjdpfx Aowta Alja Iok * Rozšíriteľný * Pohotovostná hmotnosť: 11 020 kg -----Interné číslo vozidla: 11010----Zmena a predaj počas inzerovania vyhradený. Podpora cez WhatsApp k dispozícii! V prípade otázok k vozidlu alebo ďalších informácií nás neváhajte kontaktovať cez WhatsApp. WhatsApp Nemecky, Anglicky -- WhatsApp Nemecky, Anglicky, Arabsky

Stav: nový, pohotovostná hmotnosť: 10 900 kg, maximálna hmotnosť nákladu: 37 100 kg, celková hmotnosť: 48 000 kg, konfigurácia náprav: 3 nápravy, dĺžka ložného priestoru: 9 600 mm, šírka ložného priestoru: 2 540 mm, výška ložného priestoru: 890 mm, zavesenie: vzduch, veľkosť pneumatiky: 235/75 R 17.5, farba: sivý, prevádzková hmotnosť: 10 900 kg, Výbava: ABS, Gooseneck: Hodpfouadk Nsx Aa Ijk - Gooseneck in SNT design for optimizing the loading platform length, approx. 3,700 mm long, rear chamfer approx. 1,000 mm x 6° - Technical fifth wheel load: 18,000 kg - For tractor units: 4 x 2 and 6 x 2 Loading Platform: - Loading platform approx. 9,600 mm long with rear chamfer approx. 900 mm x 6° - Platform behind gooseneck hydraulically liftable/lowerable, approx. 3,000 mm long, load capacity up to approx. 9,000 kg - Grating and 5 mm steel plate reinforcement on the chamfered section as additional strengthening Ramps: - One pair of two-piece AXS steel ramps, approx. 4,675 mm long, 900 mm wide - Grating surface - Hydraulically foldable ramp tips - Ramps can be hydraulically shifted individually approx. 235 mm outwards and approx. 365 mm inwards - Painted anti-slip sand-coating on ramp outer frame and ramp tip - Flashing lights mounted on ramp tips with switch next to ramp control panel - Quick-release ramp locks for securing in transport position Axles, Suspension, and Tyres: - BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle self-steering - 1st axle with starting aid - Operated via brake pedal of the tractor unit - Technical axle load: 12,000 kg - Air suspension with raise/lower valve - 235/75 R 17.5 - TPMS (Tyre Pressure Monitoring System) to ECE R 141 specification - TPMS sensors fitted in all wheels, including spares Braking System: - WABCO EBS-E braking system complying with EU regulations Paintwork: - Trailer MB 7350 Nova Grey Included Accessories: - Pin-type steel front wall, approx. 400 mm high - 3 kW electro-hydraulic power unit for hydraulic operations (excluding hydraulic winches) - Gooseneck guide plate for fifth wheel, approx. 500 mm wide - JOST Modul B landing gear - static test load = 50,000 kg - Continuous grating with 5 mm steel baseplate as additional reinforcement - Painted sand-coating - Cut-outs in outer frame of platform and lift bed for attaching hydraulic ramp control valves on right side of trailer - 2" king pin - Central lubricating system with 1 pump, brand BEKAMAX - On gooseneck: 1 pair removable ALU side walls, approx. 400 mm high, anodized - Electric cable winch, approx. 5,400 kg pulling force, with radio remote control - Steel cable approx. 24 m long, diameter approx. 9.5 mm, incl. cable pressure roller - WABCO Smart Board system - 4 extendable warning boards, approx. 423 x 423 mm, extendable by approx. 400 mm

Stav: použitý, maximálna hmotnosť nákladu: 42 500 kg, celková hmotnosť: 60 000 kg, konfigurácia náprav: 3 nápravy, prvá registrácia: 06/2022, with 12 split axles, hydraulically suspended, hydromechanical forced steering, rear chamfer and drive-on ramps STZ-L Gooseneck - robust steel welded construction - designed loading area 3,950 x 2,480 mm incl. chamfer - hydromechanical forced steering (dual-circuit steering) - turntable-mounted fifth wheel plate with replaceable 2 or 3.5 inch kingpin and adjustable steering wedge - kingpin load 24 t - steering radius to the rear 2,600 mm Loading area - lowered outer panels 4,630 mm, 420 mm deep enabling a loading height of 470 mm or 830 mm with floors installed - extendable by 2,053 mm - incl. aluminium bridging tracks to create a level surface - excavator arm recess at rear axles, 4,900 mm long, 880 mm wide, 480 mm deep - rear chassis length 4,900 mm incl. 500 mm chamfer, loading height 890 mm - one pair of wheel recesses in bottom loading area - hydraulically suspended 3-axle chassis - split Gigant axles with 600 mm stroke Vehicle rear - design: rear chamfer 500 mm - hydraulic rear support Drive-on ramps - 2-piece drive-on ramps, length 2,850 + 1,850 mm, width 800 mm - rubber surface with climbing strip Brake system - two-line full air brake system with diaphragm brake cylinders - automatic load-dependent braking (ALB) - automatic rod plate system (AGS) - parking brake via spring actuators - ABV brake Special equipment Radio remote control for steering and ramp operation Central lubrication system Technical Data Gooseneck Loading area (LxW): 3,950 x 2,480 mm Fifth wheel height loaded: 1,300 mm Hodpfx Aajw Etd Te Ijk Loading area Loading area (LxW): 10,030 x 2,850 mm, extendable by 2,053 mm Lowered outer panels: 4,630 mm long plus 2,053 mm extension Central girder: 980 mm Excavator arm recess: 4,900 mm long, 880 mm wide, 480 mm deep Steering 1st – 3rd axle hydromechanically forced-steered (dual-circuit steering)