Príves s pracovnou plošinou

MÜLLER-MITTELTAL 3-Achs Plateau, luftgefedert, hydr. Rampen

Stav: nový, maximálna hmotnosť nákladu: 23 500 kg, celková hmotnosť: 30 000 kg, konfigurácia náprav: 3 nápravy, dĺžka ložného priestoru: 8 380 mm, šírka ložného priestoru: 2 520 mm, Rok výroby: 2026, * PT 30 Profile: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t Gigant axles * Air suspension with lift/lower function and RtR-valve * Smart-Board infotool mounted on trailer (for axle load display – front and rear individually) * Tire pressure monitoring with display capability in the truck via EBS signal, without installation required on the truck side * Side underrun protection Iedpfx Aexptn Rogloar * Swing-out support legs at the rear of the chassis frame * Mechanically adjustable warning sign sets at front and rear * Front axle: plastic quarter mudguards with spray protection * Rear axle: straight, galvanized steel skirts with spray protection * Reflective contour marking strips on sides and rear * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at the rear * Drawbar 1,200 mm long with 40 mm towing eye and height adjustment via draw spring & turnbuckle * Toolbox made of galvanized sheet steel, approx. 650 x 300 x 600 mm, black powder-coated, mounted right side * Storage box in the turntable for accessories, with hinged lid, 2 container locks permanently installed (directly after turntable platform) * ROBOT-welded anti-slip surface on the steel plate of the turntable platform (projecting weld beads) * Load securing package including: 2 lashing eyes (13.4 t) at front left & right on the bulkhead beam, 1 pair each of UVV lashing rings (13.4 t) at front & rear, and 3 pairs each side of UVV lashing rings (10 t), pivotable and lowerable, loadable in all directions and recessed in the outer frame; 3 stake pockets per side, each with 2 t lashing capability * 6 pairs of mechanical folding outriggers for 3-meter overall width (not in rear bevel) * Width boards stored centrally on the loading platform * Hydraulic one-piece loading ramps, approx. 3,000 x 720 mm * Mechanically adjustable sideways * 4-way valve block for future retrofitting of hydraulic ramp adjustment * Continuous excavator arm rest above rear axle up to end beam (total length approx. 2,100 mm) * 2 pairs lashing eyes LC 6,400 daN in excavator arm rest, mounted laterally in the longitudinal frame * 2 galvanized steps at the turntable, left and right * Profifix lashing rail in the center axis, in flat area for lashing up to LC 3,000 daN * Chassis, turntable, folding outriggers, drop legs and loading ramps hot-dip galvanized * Axles, slewing ring, air tank, and drawbar painted in black * Loading edge height approx. 910 mm +/- 20 mm with air suspension * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Available approx. from CW 22/2026 * Sample photos

Stav: použitý, pohotovostná hmotnosť: 10 900 kg, maximálna hmotnosť nákladu: 43 600 kg, celková hmotnosť: 54 500 kg, konfigurácia náprav: 3 nápravy, prvá registrácia: 04/2025, dĺžka ložného priestoru: 8 700 mm, šírka ložného priestoru: 2 550 mm, výška ložného priestoru: 855 mm, veľkosť pneumatiky: 245/70 r17.5, farba: sivý, Rok výroby: 2025, prevádzková hmotnosť: 10 900 kg, Výbava: ABS, Gooseneck, rigid, in central tube design: - Enclosed outer frame with cutouts for lashing straps (LC 1,500 daN) - Steel flooring with anti-slip coating - Including perforated rail for aluminum approach ramps - 2" king pin - Mechanically operated BPW landing gear Iajdpfei Ai E Rox Aglor - 550 mm long, 8° bevel at the rear end of the gooseneck - Front bulkhead including stowage position for rear wall, 400 mm high - Spare wheel holder mounted upright at the front of the gooseneck - 3 pairs of recessed lashing rings LC 5,000 daN on the gooseneck deck - Aluminum drop-in sideboards, 400 mm high, consisting of 2x sideboards (length 3,150 mm) and rear board with stanchions (galvanized) - Rectangular storage box, aluminum, with folding lid and lockable, approx. 400 x 800 mm, centrally mounted - Storage box 45’, aluminum, with folding lid and lockable, approx. 400 x 800 mm, left side - Storage box 45’, aluminum, with folding lid and lockable, approx. 400 x 800 mm, right side Load platform, single telescoping: - Enclosed outer frame with cutouts for lashing straps (LC 1,500 daN) - Fixed section at front 700 mm - Steel tread plate with anti-slip coating - Beveled transition between fixed section and load platform for attaching bridging rails and wheel recesses - Excavator recess including elongated holes for load securing (LC 1,500 daN), approx. 3,850 mm long - Prepared for hydraulic ramp (electric supply fitted) - Beams for extension to 3,000 mm width - Beveled vehicle rear, 8°, 550 mm long - Sled-type design for easy mounting and removal of ramps - Continuous rear mudflap - 1 pair of lashing points LC 10,000 daN centrally on the platform behind the gooseneck - 7 pairs of lashing points LC 10,000 daN on outer frame of the platform - 6 pairs of stake pockets 100 x 50 mm on the outer frame of the platform - 1 pair of lashing points LC 10,000 daN centrally at the rear of the platform - 1 pair of stake pocket rails approx. in the middle of the platform - 1 pair of stake pocket rails on the fixed section - 1 pair of stake pocket rails behind the last axle Ramps: - Hydraulic twin-fold ramps, 2,750+1,500x800 mm - Larch timber decking - Operated via remote control (either wired or wireless) - Ramps with quick-change (removal system) Chassis: - BPW ECO Max axle make - 2 ride heights - 4 axles, each 10 t (technically 12 t) - Twin tires 245/70 R17.5 - 2 rigid axles and 2 friction-steered axles - Reverse steering lock for friction-steered axles via reverse gear - Brake system make Knorr (in accordance with EU directives with EBS-E) - TIM G2 by Knorr (Trailer Information Module) - RSS (Roll Stability Support) - Load-dependent lift axle on the first axle including starting aid (forced lowering of lift axle via TIM possible) Accessories: - 4 wheel chocks with holder - 2 pairs of warning boards 423 mm x 423 mm, with 2 marker lights and mounting position for beacon, continuously adjustable up to 3,950 mm - Mounting options on gooseneck and platform (alternatively on ramp, if present) are included - Insertable bulkhead at the end of the excavator recess - Electro-hydraulic unit for ramp operation - Wireless remote control for ramp operation - Hydraulic stabilizer legs at vehicle rear for support during loading - 1 pair of additional reversing lights at the rear, activated with reverse gear - Larch wood extension beams (option)

Stav: nový, maximálna hmotnosť nákladu: 36 020 kg, celková hmotnosť: 45 000 kg, konfigurácia náprav: 3 nápravy, dĺžka ložného priestoru: 13 600 mm, šírka ložného priestoru: 2 540 mm, zavesenie: vzduch, veľkosť pneumatiky: 435/50 R 19.5, farba: sivý, Výbava: ABS, Loading Platform: - Loading platform with extendable design featuring pneumatically operated locking system - 2 pairs of lashing rings (LC 5,000 daN) - 1 pair of lashing rings (LC 10,000 daN) - 6 pairs of outward-folding lashing rings (LC 5,000 daN) - 2 pairs of outward-folding lashing rings (LC 10,000 daN) - Cutouts in the outer frame of the loading platform for attaching tensioning straps Axles and Tyres: - BPW axles, air-suspended, with disc brakes (377 mm), equipped with lifting/lowering function - Self-steering axles with electromagnetic reverse lock, activated via reverse gear or manually - Axle tools - Tyres 435/50 R 19.5 Iajdpfxei Dwlws Agljr Brake System: - Brake system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - Premium, long-lasting corrosion protection of the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer - High-quality single-tone 2-component (2K) topcoat in Novagrau - Rear section metallized and painted in RAL 9010 (Pure White) - Metallic paint finish not possible Landing Legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Steel Construction: - Steel construction made from high-tensile fine-grain steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical System: - Electrical system compliant with EU regulations, lighting 24 Volt ASPÖCK-NORDICK (ASS3) - ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets - Connection as per ISO - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Included Accessories: - Yellow-red air couplings on the galvanized front connection bar - 2 wheel chocks with holder - 2" kingpin - A galvanized steel front wall, approx. 1,600 mm high - Yellow reflector tape in accordance with EU regulations on the sides, extension section, and rear of the trailer - European reflector plates (Red-Yellow) at the rear of the trailer - Loading platform with approx. 38 mm thick hardwood flooring - 10 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the platform - 1 spare wheel holder under the loading platform on the right-hand side in the direction of travel - Manual and description on USB stick - 1 mudflap at the rear of the trailer - 1 bracket for a beacon at the rear of the trailer - On the gooseneck and the rear plate, left and right, each with bracket for warning signs including socket - 1 INOX toolbox mounted crosswise under the platform (1,000 x 400 x 2,500mm) - 6 pairs of WADER container pockets in the platform, for 1x 20ft container, 2x 20ft containers or 1x 40ft container; an additional locking point is provided in the extension section for a 45ft container - 3 pairs of stake pocket strips, mounted transversely in the platform, for plug-in stakes 100 x 50 mm - 60 km/h speed sticker at the rear - 2 reversing spotlights mounted on the rear plate - Four warning signs extendable by approx. 400 mm (approx. 423 x 423 mm) each with a position lamp - Bracket for beacon on the warning signs - HRM metallization (High Resistance Metallization) of the outer frame - Complete steel construction shot-blasted, then all defined visible surfaces metallized and hot-finished with ZINACOR 850 (85% zinc – 15% aluminium)

Stav: použitý, maximálna hmotnosť nákladu: 42 700 kg, celková hmotnosť: 58 600 kg, konfigurácia náprav: 3 nápravy, prvá registrácia: 07/2013, Výbava: ABS, Vehicle ID No.: YAFTL313000014136 First registration: 18.07.2013 German MOT (HU) due Unladen weight: 15,900 kg Iajdpjr Dplmsfx Agler Overall length: 16,700 mm Gooseneck: 3,700 mm Swing radius king pin to rear: approx. 2,700 mm Standard king pin 3.5 inches – Coupling height: 1,320 – 1,350 mm Low bed length: 8,500 mm – Loading height: approx. 500 mm Extendable by 4,250 mm Chassis frame: 4,500 mm – Loading height: approx. 900 mm Suspension travel (with air suspension): approx. -80/+160 mm Excavator trough – Bucket arm recess Hydraulic support legs Technical fifth wheel load up to 25,000 kg Axle loads: 3 x 11,200 kg Axle spacing: 1,360 mm SAF axles with drum brakes 3 x hydraulically forced-steered axles with RADIO + cable remote control Tyres: 235/75 R 17.5

Stav: použitý, najazdené kilometre: 480 662 km, výkon: 375 kW (509,86 k), prvá registrácia: 01/2022, typ paliva: nafta, celková hmotnosť: 18 000 kg, konfigurácia náprav: 2 nápravy, brzdy: retardér, farba: biely, typ prevodu: automatický, emisná trieda: Euro 6, Výbava: ABS, klimatizácia, navigačný systém, nezávislé kúrenie, sadzový filter, Identifikačné číslo vozidla: WMA13KZZXNP182137 Prevádzková hmotnosť: 8 132 kg Dátum prvej registrácie: 26.01.2022 Pravidelná technická kontrola: splatná XLX kabína vodiča Iajdsr Agicopfx Aglor RETARDER, digitálny tachograf Automatická klimatizácia, nezávislé kúrenie, 2 lôžka, rádio USB/Bluetooth/navigácia, príprava na mýto, multifunkčný volant, chladnička, vyhrievané sedadlo, adaptívny tempomat, upozornenie na vzdialenosť, asistent jazdných pruhov, asistent odbočovania, Vzduchové pruženie predná / zadná náprava Palivová nádrž: 480 l + 480 l Výška sedla: 980 mm Rázvor: 3 600 mm Spojler kabíny Obutie: 1. náprava 315/60 R 22.5 2. náprava 295/60 R 22.5 Zmeny, medzičasný predaj a chyby sú výslovne vyhradené. Tento popis slúži na všeobecnú identifikáciu vozidla a nepredstavuje záruku v právnom zmysle. Záväzný je popis uvedený v kúpnej zmluve. Naša ponuka je spravidla bez novej STK. V prípade záujmu o novú STK Vám radi predložíme ponuku od našich partnerských servisov! Vozidlo môže obsahovať reklamu alebo polepy. Platné sú naše všeobecné obchodné a platobné podmienky.

Stav: nový, pohotovostná hmotnosť: 10 600 kg, maximálna hmotnosť nákladu: 39 400 kg, celková hmotnosť: 50 960 kg, konfigurácia náprav: 3 nápravy, dĺžka ložného priestoru: 9 300 mm, šírka ložného priestoru: 2 540 mm, výška ložného priestoru: 760 mm, zavesenie: vzduch, veľkosť pneumatiky: 205/65 R17.5, farba: sivý, prevádzková hmotnosť: 10 600 kg, Výbava: ABS, Gooseneck: - Gooseneck with 30 mm hardwood floor - Gooseneck in straight design at the rear - 3 pairs of lashing rings (LC 5,000 daN) Extendable loading area: - Loading area in extendable version - 5 pairs of lashing rings foldable outwards - 3 pairs of lashing rings foldable outwards - 1 pair of lashing rings laid flat at the front of the loading area - Cut-outs in the outer frame of the loading area for attaching tension belts - Hardwood flooring approx. 48 mm thick, over the axles with checker plate covering Landing legs: - JOST mechanical landing legs with 2-speed gearbox for 24t lifting capacity (50t test load) Axles and tyres: - BPW axles, two rigid, two trailing steering axles - Air suspension, with drum brakes, with lifting/lowering function - The trailing steering axles with electro-magnetic reversing lock, can be activated either via reverse gear or manually - Axle tools - Tyres 205/65 R17.5 Brake system: - Brake system in accordance with EU regulations with EBS-E (4S3M) Steel construction: - Steel construction made of high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system in accordance with EU regulations, 24-volt lighting, ASPÖCK-NORDIK (ASS3) Iaodpfst Ag Uwjx Aglor - ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets - Connections according to ISO: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Paintwork: - First-class and long-lasting corrosion protection of the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer - High-quality 2-component (2K) top coat, single-colour in Novagrau - Rear section metalized and painted in RAL 9010 (pure white) Included accessories: - One spare wheel with holder in front of the front wall - 2" kingpin - Galvanized steel front wall approximately 400 mm high - Yellow-red air couplings on the galvanized connection bar at the front - 4 wheel chocks with holders on the front wall - Galvanized folding supports under the sloped loading area - Bracket for a revolving beacon at the rear of the trailer - Galvanized, extendable width approx. 230 mm per side - White reflective tape to EU regulations on the side, at the extension, and red at the rear - At the gooseneck and on the rear plate, left and right, one bracket for warning signs each, including socket - European reflective warning plates (red-yellow) at the rear of the trailer - TPMS tyre pressure monitoring system according to ECE R 141 - On the gooseneck, plug-in aluminium side and rear panels approx. 2,440 x 400 mm - The rear, galvanized plug-in stakes are removable, length of the structure approx. 2,560 mm - 7 pairs of WADER container locks - 1x 20ft container on the loading area; 1x 40ft container on the loading area; 1x 40ft container above the gooseneck; 2x 20ft containers - 7 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame of the loading area - Lift axle at the front axle controlled by TEBS E, depending on current axle load and load condition - Movable hanging bar for aluminium approach ramps at the rear of the vehicle - On checker plates on the gooseneck and loading area, a painted-in sand layer as anti-slip protection - Four warning signs each extendable by approx. 400 mm, size approx. 423 x 423 mm, with position light - On warning signs, bracket for rotating beacon - 80 km/h speed stickers on the rear and both sides - Load manometer for determining axle l

Stav: nový, pohotovostná hmotnosť: 7 900 kg, maximálna hmotnosť nákladu: 41 600 kg, celková hmotnosť: 49 500 kg, konfigurácia náprav: 3 nápravy, dĺžka ložného priestoru: 8 600 mm, šírka ložného priestoru: 2 540 mm, výška ložného priestoru: 860 mm, zavesenie: vzduch, veľkosť pneumatiky: 235/75 R 17,5, farba: sivý, prevádzková hmotnosť: 7 900 kg, Výbava: ABS, Gooseneck: - Gooseneck with rear taper approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, 30 mm thick Loading Platform: - Loading platform with rear taper approx. 1,000 mm x 8° - Recess in the sloped section and extending into the loading platform for the excavator bucket stick, approx. 2,900 x 750 x 210/290 mm - Cut-outs in the outer frame of the loading platform for attaching tensioning straps - Hardwood flooring approx. 48 mm thick, over the axles with checker plate covering Landing Legs: - JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Axles and Tyres: - BPW axles and suspension, 2 fixed axles, 1 trailing-steer axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated by reverse gear and manually - Air suspension with lift and lower valve - TPMS tyre pressure monitoring system according to ECE R 141 - Tyres 235/75 R 17.5 Paintwork: - Complete steel structure automatically shot-blasted after welding with turbine blasting unit - Second blast treatment with corundum for optimal adhesion of the coating system - Final coating with 2 coats of 2K topcoat, single colour in RAL MB 7350 Novagrau - Rims painted silver - Rear section metallised and painted in RAL 9010 (Pure White) - Cavities sealed with special wax Electrical System: - Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX on the front connector strip with sockets: 2x 7-pin & 1x 15-pin Included Accessories: - Extensive lashing positions - 2" king pin - One galvanised steel front wall approx. 400 mm high - Yellow-red air couplings on the galvanised front connector strip - 4 wheel chocks with holder on the front wall - Mounting at the rear of the gooseneck for ALU loading ramps - Galvanised folding supports under the sloped rear section of the loading platform - A holder for a beacon at the rear of the trailer - Galvanised, extendable side extensions approx. 230 mm each side - White reflective tape on the sides and red on the rear in accordance with EU regulations - At the gooseneck and rear plate, left and right, each with a holder for warning plates including socket - On the gooseneck, plug-in ALU side and rear boards approx. 2,440 x 400 mm - The rear, galvanised stakes are removable - 2 pairs of WADER container locks in the loading platform for a 20 ft container - 6 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading platform - Sliding mounting rail for ALU loading ramps at the rear of the vehicle - 20 x 20 mm square climbing strips every 200 mm on the outer frame of the sloped section of the loading platform - Painted-on sand coating as anti-slip protection on the checker plates of the gooseneck and the loading platform - Four warning plates extendable by approx. 400 mm, approx. 423 x 423 mm each, with position light - Holder for beacon on the warning plates - 80 km/h speed stickers on the rear and on both sides - European reflective panels (red-yellow) at the rear of the trailer - Manual and documentation on USB stick Ijdpjunrapjfx Aglsar - HRM metallisation (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then the defined visible areas are hot-finished with ZINACOR 850 metallisation (zinc 85% - aluminium 15%)