Nízkopodlažný náves na prepravu stavebných strojov

Faymonville 4-1+3-A-Semi-Twinaxle II-Rampen-MultiMAX

Gooseneck:
• Gooseneck in SNT design for load area length optimization, approx. 3,700 mm long, tapered at the rear approx. 1,000 mm x 10°
• For tractor units: 4 x 2, 6 x 2, and 6 x 4

Load area:
• Load area with extendable design, approx. 8,800 mm long with rear taper approx. 500 mm x 10°
• Recess in the load area and extending into the taper for excavator dipper stick accommodation, approx. 3,950 x 580 x 370/450 mm

Ramps:
• One pair of two-piece steel ramps, approx. 4,350 mm long and approx. 900 mm wide
• Hydraulically folding ramp tips
• Ramps individually hydraulically adjustable approx. 235 mm outwards and approx. 215 mm inwards
• Hardwood covering on the tapered rear of the load area
• Ramp with hardwood covering
• Square climbing strips, 20 x 30 mm, spaced approx. every 200 mm on the outer ramp frame

Axles and tyres:
• TWINAXLE-II independent wheel suspension with BPW axle stubs, 1st axle with steering control ahead of pivot, all other axles hydromechanically forced steering
• 1st axle with electromagnetic reverse lock activated via reverse gear or manually
• Technical axle load: 12,000 kg
• Hydraulic axle levelling, hydraulic cylinders with shut-off valves
• Tyres: 245/70 R 17.5
• TPMS tyre pressure monitoring system in accordance with ECE R 141

Accessories included:
• Plug-in steel front wall, approx. 400 mm high
• 4 wheel chocks with holder
• Yellow-red air couplings on the front connection bar
• 3 kW electro-hydraulic unit for controlling hydraulic functions, except hydraulic winches
• 1 spare wheel
• 2 pairs of screw-in lashing rings
• 1 pair of lying lashing rings in the rear area of the gooseneck
• On the gooseneck: 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized
• On the gooseneck: 1 plug-in ALU rear board, approx. 400 mm high, anodized
• Hardwood covering approx. 40 mm thick over the gooseneck, checker plate covering over the kingpin
• 3.5" kingpin
• Gooseneck guide plate for the fifth-wheel plate, approx. 500 mm wide
• Load area locking with conically welded locking profiles every 250 mm
• Pre-tensioning plate included
• 1 pair of lashing rings on the front cross member
• 8 pairs of recessed lashing rings in the outer frame of the load area, foldable to the outside
• Extensions (galvanized) extendable by approx. 230 mm each side
• 1 pair of fixed wheel recesses, open up to extension, approx. 700 x 410 mm, in the load area in front of the 1st axle
• Wheel recesses with sheet steel covering and square climbing strips 15 x 15 mm, spaced approx. every 200 mm
• 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm, in the load area between the 1st and 2nd axle
• Wheel recesses with square climbing strips 15 x 15 mm and extensions in the lower section
• ALU covers for wheel recesses between the 1st and 2nd axle, can also be used as extension planks
Crsdpsrvw U Ssfx Aa Ija
• 1 pair of mechanical rear supports
• Square climbing strips, 20 x 30 mm, spaced approx. every 200 mm on the outer frame of the rear taper of the load area
• Central lubrication system with 1 pump, brand BEKAMAX, with standard grease per NLGI-2
• Radio and wired remote control, with 2 indicator lights on the receiver as single track control
• WABCO Smart Board system
• The Smart Board is equipped with an odometer
• 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for rotating beacon

Inzerát bol automaticky preložený. Chyby v preklade sú možné.