Trojsmerný sklápačský príves

MÜLLER-MITTELTAL 11,9 to Tandemkippanh. mit Agra vorbereitung

Stav: nový, maximálna hmotnosť nákladu: 8 650 kg, celková hmotnosť: 11 900 kg, konfigurácia náprav: 2 nápravy, dĺžka ložného priestoru: 5 000 mm, šírka ložného priestoru: 2 420 mm, výška ložného priestoru: 500 mm, Rok výroby: 2026, * KA-TA-R 11,9 Masterline ----Brzdy: * Wabco EBS * Núdzové uvoľňovacie zariadenie pre pružinové akumulátorové valce * Bubnové brzdy ----Nápravy: * 2 x 5,5 t BPW nápravy ----Odpruženie: * Listové pružiny s tandemovým vyrovnávacím agregátom ----Ťažné zariadenie / prírubové ťažné oko: * Ťažné zariadenie s výškovo nastaviteľným rozsahom 300 mm a prírubovým ťažným okom 40 mm ----Elektrická inštalácia / osvetlenie: * Systém monitorovania tlaku v pneumatikách (TPMS) * Multivoltáž * 15-pólová zásuvka * 12 V 13-pólový prídavný kábel * Predĺžené spojovacie káble pre poľnohospodárske a lesnícke ťahače * LED koncové svetlá ----Všeobecné montážne diely: * Mechanické podporné nohy vpredu * Vzadu 2 mechanické sklopné podpery * Plastová skrinka na náradie na pravej strane * 2-stupňový nášľap v smere jazdy vpredu vľavo * Spodný ochranný kryt upevnený skrutkami * Plastový blatník ----Vyklápacia nadstavba: * Sieťové háky na bočných a zadných stranách v ložiskách centrálneho zamykacieho systému, ako aj 2 kusy na čelnej stene * Oceľová 3-stranná vyklápacia nadstavba (s priebežnými bočnými stenami - bez stredových priečok - sklopiteľná s pružinovými zdvihákmi bočnice, sklopiteľná zadná klapka a kyvadlová cez manuálne centrálne zamykanie) * 4 mm oceľová podlaha * Upevňovacia lišta vzadu pre nakladacie rampy ----Upevnenie nákladu: * V každom rohu 1 x 5 t upevňovací popruh * Ako aj na bočných stranách po 4 x 3 t upevňovacie očká zabudované do vonkajšieho rámu ----Rampy: * 1 pár hliníkových nakladacích ramp s rozmermi približne 3 310 x 400 mm (nosnosť 8 t / pár), vhodné pre vozidlá s pneumatikami a pásovými vozidlá * Zamykateľný úložný priestor vzadu pod ložnou plochou, zabudovaný do rámu ----Pneumatiky: * Pneumatiky 385/55 R 19,5 ----Lakovanie: * Rám, ťažné zariadenie, vyklápacia nadstavba, čelná stena, sklopné podpery a zadné priečky žiarovo zinokované * Nápravy, pružiny, vzduchový zásobník, prírubové ťažné oko a podporné nohy lakované v čiernej farbe * Lakovanie bočníc v odtieni RAL - 9010 čisto biele ----Informácie: * Nadstavba je zosilnená s certifikátom pre upevnenie nákladu podľa EN 12642 XL * Nové vozidlo so zárukou výrobcu * Chyby a predaj vyhradené ----Dodacia lehota: * Dodanie možné od cca 47. týždňa 2026 Tedel Thw Ijpfx Andec

Stav: nový, maximálna hmotnosť nákladu: 37 390 kg, celková hmotnosť: 48 000 kg, konfigurácia náprav: 3 nápravy, Rok výroby: 2026, * TS 3 RM ML 30.0: Tsdpfxetpta De Andec ----Brakes: * Wabco EBS-E (Electronic Braking System) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Start-up aid for shunting purposes engaged on the first axle via EBS (without truck-side installation) * Last axle as a trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle from the cab for shunting purposes, operated via EBS (without truck-side installation) ----Suspension: * Air suspension with lifting and lowering function as well as RtR valve ----Electrics / Lighting: * Smart Board mounted as an info tool on the trailer with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at the rear * 2 additional LED reversing lights * 7-pin socket at the rear for overlength lighting * Side marker lights with indicator control * Tire pressure monitoring system with display function in the truck via EBS signal (without truck-side installation) ----General attachments: * Side underrun protection * Landing legs at the front and swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder in front of the front wall cross member (without spare wheel) * Mechanically adjustable warning signage packages at the front and rear * Swivel arm as carrier for connection lines from the truck to the semi-trailer ----Low-bed loading area: * 2nd king pin position * Fifth wheel platform with 45° beveled front corners and a front toolbox made of galvanized, powder-coated sheet steel, W = 2,480 x H = 500 x L = 665 mm with hinged lid * 400 mm aluminum side boards on the fifth wheel platform (custom RAL color), foldable and removable * Rear wall -150 mm- slotted in * Rear chamfer on the fifth wheel platform to low-bed, approx. 700 mm long with checker plate cover and at the end a perforated strip for hooking in aluminum approach ramps * Fifth wheel platform with 50 mm clamped wooden floorboards, and low-bed platform with 60 mm clamped wooden floorboards * Checker plate above the axles * 9 mechanical folding wideners to 3 m total width, but not on the rear chamfer (widening planks available with closed storage box transversely under the loading area) * 3 receiver shafts under the fifth wheel platform for optional storage of aluminum approach ramps or wooden planks for covering wheel recesses ----Load securing (LaSi Package): Fifth wheel platform: * Perforated outer frame bent at 45°, with hole pattern for lashing equipment (2 t lashing capacity per point with a minimum spacing of 480 mm) * Each side: 3 x 13.4 t lashing rings recessed in the floor (1 x on the fifth wheel platform, 1 x on the longitudinal beams after the kick-up, 1 x above the middle axle next to the longitudinal beam) Low-bed platform: * Each side: 3 x 13.4 t lashing rings on the outer frame (1 x at the start of the fifth wheel platform kick-up, 1 x at the beginning of the approach ramp, 1 x at the end of the approach ramp) * Each side: 2 x 10 t lashing rings (1 x between front wheel recess and 1st axle, 1 x between the 2nd and 3rd axle) * Each side: 3 x 5 t lashing rings bolted to the outer frames of the wheel recesses (2 at the front wheel recess, 1 at the rear wheel recess) ----Excavator arm trough: * Extended excavator arm trough, continuous from end of last rigid axle over steering axle to end cross member, with inner reinforcement profile approx. W = 770 mm x D rear = 27

Stav: nový, maximálna hmotnosť nákladu: 28 860 kg, celková hmotnosť: 37 000 kg, konfigurácia náprav: 3 nápravy, Rok výroby: 2026, * Wabco-EBS-E (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t axles * Air suspension with lifting and lowering function as well as RtR valve * Maneuvering aid for shunting purposes activated on the first axle via EBS – no truck-side installation required – when the lift axle is raised + 30 mm ride height * Smart-Board as infotool mounted on trailer with pressure sensors for total axle load display * Last axle as trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle from the driver's cab for maneuvering via EBS (without truck-side installation) * 2" king pin * 1 axle liftable * Lateral underrun protection * Front aluminium drop-down supports and rear swing-down supports on the chassis * Alcoa LVL One aluminium rims * 15-pin electrical connector * LED lighting 12 / 24 V * Removable rear LED beacon * 2 additional LED reversing lights * 2 LED work lights mounted on trailer sides – without truck-side installation * 7-pin socket at rear for overlength lighting * Side marker lights with indicator activation * Tire pressure monitoring with display option in truck via EBS signal (no truck-side installation required) * Mechanically adjustable warning sign packages front and rear * Straight steel wheel arches * Saddle platform with 45° beveled front corners and front toolbox made of galvanized, powder-coated sheet steel W = 2,480 x H = 500 x L = 665 mm with top folding lid and side doors in the beveled corners * 400 mm high aluminium drop sides (RAL 9010 pure white) foldable and removable on the sides of the saddle platform * Rear wall -150 mm- slotted in high * Rear incline on saddle platform to lowbed approx. 700 mm long with checker plate, with a perforated strip at the end for hooking in aluminium loading ramps * Saddle platform and lowbed deck with 50 mm clamped wooden planks * Tread plate over the axles * Preparation for 3 storage compartments under the saddle platform for optional aluminium loading ramps * Swing arm as carrier for connection lines from truck to trailer * Load securing package consisting of: perforated outer frame on saddle platform, 45° angled with hole pattern for lashing equipment (2 t lashing force per point at a min. distance of 480 mm), 2 x 6.3 t recessed lashing rings on each side in the floor, 1 x 16.5 t lashing ring on each side in the approach slope from the low-bed platform to the saddle platform, 2 pairs of 16.5 t lashing rings on low-bed platform (1 x on longitudinal members after the cranking and 1 x over the middle axle next to the longitudinal member), 3 x 13.4 t lashing rings on each side on the outer frame (1 x at the start of the saddle platform cranking, 1 x at the start of the approach slope, 1 x at the end of the approach slope), 3 x 10 t lashing rings on each side (2 x between the front wheel recess and 1st axle, 1 x between 2nd and 3rd axle), 3 x 5 t lashing rings on each side bolted to the outer frames of the wheel recesses (2 on the front and 1 on the rear wheel recess) * Extended excavator boom trough from the end of the last rigid axle over the steering axle to the rear crossmember, continuous with internal reinforcement profile approx. W = 770 mm x D rear = 270 mm / Depth front 170 mm, with 2 x 6.4 t lashing rings each side in the excavator boom trough * 2 wheel recesses on each side, 390 mm deep and 640 mm wide for transport of wheel loaders with a wheelbase of 3,000 – 3,590 mm and tire diameter of 1, Tsdpfjwh Hdxsx Andsc