Nízkopodlažný náves

Meusburger 3-A-Semi-hydr.Ladebod.-abklappbares Heck

Stav: použitý, pohotovostná hmotnosť: 10 500 kg, maximálna hmotnosť nákladu: 31 000 kg, celková hmotnosť: 41 500 kg, konfigurácia náprav: 3 nápravy, prvá registrácia: 10/2020, dĺžka ložného priestoru: 9 950 mm, šírka ložného priestoru: 2 550 mm, výška ložného priestoru: 890 mm, zavesenie: vzduch, veľkosť pneumatiky: 235 / 75 R 17.5, farba: sivý, Rok výroby: 2020, Výbava: ABS, For every used trailer, you receive a current and comprehensive inspection and functional report. Frame: - Steel frame welded construction with front frame drop and flat low bed platform - Neck of the frame 165 mm with external longitudinal beams for extended low bed Lrodjywu Rfepfx Ag Tji - With Wirtgen slope on drop plateau approx. 850 x 65 mm - 2-inch kingpin - Support for folded-down tail section when used as a ramp Front wall: - Aluminum front wall with beveled corners, 1,000 mm high - Inside front wall lined with aluminum checker plate 3/5 mm over entire height and width - Grid attachment above the front wall with 2 hooks for attaching lashing chains - Box for steering, electrohydraulic motor, and winch set approx. 150 mm inward (steering and motor boxes stacked) Floor: - Grating 30/30/5 mm over entire loading area in the low bed and on the high bed - For foldable tail in main frame 40/30/25/5 - Load bar aligned longitudinally to direction of travel, thickness 5 mm, height 30 mm or 40 mm - Grating laid over longitudinal beams, flush with the outer frame Axles and Tires: - 3 x 10,000 kg BPW air suspension axles with S-cam brake (300/200 mm), airbag diameter 360 mm - Last axle with steering, automatically locking during reverse and manually lockable if required - 1st axle is a lift axle (controlled via SmartBoard) - Automatic slack adjusters - Axle spacing 1,310 mm / 1,410 mm - Wabco SmartBoard with ECAS function - Air suspension with lift and lower valve - Tires 235/75 R 17.5 Foldable rear with extension: - Entire loading surface behind axle assembly hydraulically foldable - Ramps can also be positioned with the tip onto a solid concrete ramp for loading (both with extended extension and retracted) - Load capacity of the foldable tail section: - 10 t axle load (5 t wheel load) in horizontal position as loading area - 22 t drive-over capacity when used as a ramp, if rear support (= underrun protection) rests on the ground - Support leg, foldable and height-adjustable - Support leg length designed for ramp loading at a ramp height of 1,100 – 1,300 mm - Operation via electrohydraulic unit powered through NATO socket from the towing vehicle - Pump unit mounted on the outside front wall via connectors - Separate radio remote control for table lift and foldable tail - Hydraulic control in stainless steel toolbox 500x350x400 mm, fitted right side (in direction of travel) in front of axle assembly - Rear foldable tail can also be raised approx. 60 degrees upwards, thus shortening the loading area by approx. 1,300 mm - Rear extension: hydraulically extendable rear extension, 3-sections (each approx. 800 mm wide), can be extended approx. 2,000 mm, operated via hydraulic pump unit Accessories included: - Hydraulically liftable ramp at the frame drop for driving onto the high bed over the entire vehicle width, drivable up to 6 t, without drive-on plate but with angle welded at drop - Vertical abrasion protection and upper stop at the frame drop for exact positioning when raised - Ramp is secured by holding valve - 9 lashing rings in center longitudinal row countersunk into the loading area, plus 1 foldable lashing ring in front of the king plate in the center - 1 pair of 8 t foldable lashing rings in front of the front wall - 2 PVC toolboxes - Radio remote control for hydraulic lift and lowering operations for lift bed and foldable tail