Sklápací náves

STAS V-9.70 light 53m³

Chassis, light version
In aluminium (15-6-12)
Two fully automatic welded I-beam longitudinal members with welded cross members. Chassis width: 1,600 mm
Axles & Suspension: Disc brakes 430 mm, "off-road version" SAF-Intradisc light axle units, 3 x 9 t with SAF air suspension,
centrally mounted to the chassis longitudinal member, 1st axle with liftable air bellows and start-assist, manual forced lowering,
Smart Board info center, lowering valve, front loading pressure gauge

Tyres and wheels on aluminium rims
6 wheels with 385/65 R 22.5 tyres, approx. 50%, 11.75x 2.5 ET 120, universal wheel bolts for aluminium rims

Gbjdsyiw T Ejpfx Ag Teh
King pin:
2", screwed into an 8 mm thick "light" plate

Landing legs:
Support winches, 2x20t load capacity, with swivelling base plate for air suspension

Brake system:
according to E.C. standards, dual-line system Wabco, spring-loaded parking brake acting on two axles,
and Wabco EBS-E incl. RSS (Roll Stability System), Wabco Smartboard info center, aluminium air reservoir

Electrical system:
as per StVZO guidelines with 3 round three-chamber lights type Aspöck, 24V system with 2x7 and 1x5 pin sockets,
with 2x7 side marker lights, 2 LED reversing lights centrally at the rear, 1 round fog lamp, 4 LED work lights,
1 interior LED lamp, 4 red LED position lights in the rear frame
All air and electrical lines neatly routed in plastic conduits!

Tipper body/smooth-side design - fully welded interior
Aluminium tipper body, side walls made of 30 mm thick board profiles (2-3 mm), 600 mm wide, welded, floor 8 mm thick, high abrasion resistant
alloy (5383H34/HB 110) with 90 degree profile to the side wall, front wall 4 mm reinforced, straight design, tailgate as
a universal door in straight design with 2 wing doors (1/2-1/2 version) with grain chute, operation of universal door automatic-pneumatic with separate lever, lockable, tail frame in ALU, swingable, two hold-down brackets with rubber buffers fixed between the tipper body and the frame at the front wall,

Hydraulic system: Tipping cylinder with "jacket" suspension
Hydraulic cylinder mounted on the front wall, working pressure 150 bar, make Edbro with approx. 2.5 m hydraulic hose and
loose half 1", tipping angle approx. 48 degrees

Accessories
6 Parlok mudguards, complete spray flap across full vehicle width attached to underrun guard, no spare wheel holder ALU, foldable side underrun protection right,
large toolbox type 860, approx. 3 m aluminium ladder, 3 aluminium swing stanchions raised approx. 150 mm, additional stanchion supports centre,
roll tarp with central light strip and separate reinforcements in wear areas, quality approx. 660 g/m2 with roll tarp system and quick release fastening,
perimeter rubber cord at rear end of tarp with two catch hooks to be fixed to rear swing stanchion, walkway on chassis, rear tarp closure with welded-in rubber cord for water protection, robust foldable underrun guard, 2 "Clear-Pass" spray flaps on the mudguard according to EU standards, side-mounted aluminium grain funnel with discharge bag, bracket for shovel, broom and scraper mounted above the axles, etc...

Unladen weight: 5,950 kg

Offer and images subject to prior sale

Inzercia bola automaticky preložená a vyskytli sa nejaké chyby prekladu.