Plošinový náves

Meusburger 3-Achs-Mega-Tele-Plateau-nlla

Chassis:
- Welded steel frame construction – lightweight design
- Neck height approx. 110 mm
- Outer frame closed on the outside
- Vehicle with extendable central frame, telescoping 7,000 mm (permitted with self-steering axle max. 4,000 mm), lockable pneumatically in 500 mm increments
- 8 mm fifth wheel plate with replaceable 2” kingpin
- Frame reinforced for point load of 25 t over 3 m when retracted
- Load-bearing outer frame
- Rear bevel 500 x 100 mm
- Front installation dimension matched to front corner 2,040 mm
- Rear underrun protection = extended rear plate
- Mounting rail at rear on end plate
- Drop-type rear landing legs

Landing Gears:
- Mechanical 24 t landing gears with single-sided operation and compensating mechanism

Axles:
- BPW air suspension axles, each with 10 t axle load, air bellows diameter 360 mm
- S-cam brake 300/200 mm, asbestos-free brake linings
- Automatic slack adjuster
- WABCO SmartBoard with lift/lower device, total lift approx. 200 mm
- 3rd axle as friction-steered trailing axle with electric and mechanical locking

Bwsdpfx Adjrx N Dve Ujw
Wheels and Tires:
- 13 steel disc wheels, 10-hole, with offset, hub-centered
- 13 tires 235/75 R17.5 tubeless

Mudguards:
- Sheet metal mudguards with spray flaps

Brake System:
- Dual-line brake system with EBS
- EBS (WABCO 4S3M)
- Aluminum air tanks
- Spring-actuated parking brake
- Yellow/red air couplings

Floor:
- 50 mm hardwood floor, approx. 5 mm projecting over the frame profiles

Front Wall:
- 25 mm aluminum hollow sections, 2,000 mm high, bolted, two supports
- 2 lashing eyes for securing the front wall as per DIN EN 12642 (5,000 daN)

Paintwork:
- Steel grit cleaning, spray galvanizing of chassis including telescopic section, primer
- Chassis and wheel hubs in MB 7350 nova gray
- Outer frame and front wall in MB 7350 nova gray
- Reflective tape on sides and rear in yellow

Accessories:
- Lateral underrun protection
- 4 wheel chocks
- 1 spare wheel carrier on the side
- Elongated license plate holder in underrun protection
- 2 ECE plates
- 3 pairs of standard lashing rings, recessed in the outer frame, mounted on the front platform, each with a lashing capacity of 4 t
- 9 pairs of heavy-duty lashing rings (foldable) each with a lashing capacity of 8 t
- 1 pair mounted at the end of the front platform, and 8 pairs mounted on the rear platform
- 6 pairs of ‘mushroom’ lugs on the side of the outer frame with 24 mm web thickness for lashing
- 8 pairs of stake pockets on the side of the outer frame for stakes sized 100x50 mm
- 3 rows of transverse stake pockets for 100x50 mm stakes (1x in kingpin area max. 100 mm deep, 1x before axle assembly, and 1x after axle assembly – 100 mm longitudinal, 50 mm transverse)
- Storage compartment for stakes in front of the front wall (= stake pockets in the floor)
- Extendable warning signs including position lights, at the front on the landing gear and at the rear before the end plate, infinitely extendable up to a load width of 4,500 mm, with 3-pin socket and detachable spiral cable
- 1 PVC toolbox 630x400x450 mm
- Container locks for 2 x 20 ft and 1 x 40 ft container

Inzercia bola automaticky preložená a vyskytli sa nejaké chyby prekladu.